News Center

创新、诚信、务实、高效

News Center
Contact us

Jiulongpo:
Address: Jiulongpo District of Chongqing Jinke Electrical and Mechanical City B District 135; Land: 023-68828132; Mobile: 15025367922
Yubei:
Address: Yubei Airport East Road, Ridge International Engineering Machinery Trading Center 11-37; Landline: 023-68921010; Mobile: 13883254999
Official website: www.combylift.com; E-mail: xp009@126.com; sales of a QQ: 2568988010; sales of two QQ: 37029430

Industry news
Are you here:Home > News Center > Industry news

When the goods are taken with

Time: 2019-09-29 18:22:06Copyfrom: 重庆旭普科技有限公司{英文版}

  When the goods are taken with the fork, the fork should be cut into the load, and the fork can not touch other goods or objects. Should use the smallest mast to tilt the load to prevent the load back sliding. When the load is released, the mast can be tilted in a small amount to accommodate the load and the fork.



  (A) view the vehicle
  (1) before the forklift work, should look at the appearance, filling fuel, lubricating oil and cooling water.
  (2) View start, work and brake functions.
  (3) view the lights, the sound signal is not completely useful.
  (4) forklift should be viewed during the operation of the pressure, the temperature is not normal.
  (5) after the forklift should also look outside the leak and timely replacement of seals.
  (6) battery forklift In addition to the above should be viewed, but also according to the battery car to view the contents of the battery forklift circuit to view.
  (B) start
  (1) before the start, observe the adjacent, to recognize the obstacles without obstruction of traffic safety, the first whistle, after the start.
  (2) pneumatic brake vehicles, brake barometer readings must meet the required value to start.
  (3) forklift in the load started, the driver should first recognize the goods contained in a stable and reliable.
  (4) start slowly and smooth start.
  (C) travel
  (1) when the fork, the bottom of the fork from the ground height should adhere to 300-400mm, mast to be tilted.
  (2) Do not raise the fork too high when traveling. Access to the work site or on the way, we should pay attention to whether there are obstacles across the scratch. When the load is moving, such as fork and rise too high, will add the overall height of the forklift center, affecting the stability of the forklift.
  (3) after unloading should first drop the fork to the normal direction and then travel.
  (4) When turning, if there are pedestrians or vehicles, should announce the signal and stop the high-speed turn. A sharp turn will cause the vehicle to lose its lateral stability and tilt.
  (5) internal combustion forklift in the downhill is strictly prohibited flame glide.
  (6) non-special circumstances, to stop the load in the brakes.
  (7) When the load travels more than 7 degrees and is above and below the speed of the block, the brake shall not be used for non-special conditions.
  (8) forklift in the operation to comply with the provisions of the factory traffic rules, it is necessary with the front of the vehicle to maintain a certain safe distance.
  (9) When the forklift is running, it is necessary that the load be at the lowest azimuth without obstructing the movement. The gantry should be properly tilted, and the load shall not be increased during stacking or loading. In the handling of large objects, the object to block the vision of the driver, then should open the forklift.
  (10) forklift from the rear wheel control steering, so it is necessary to pay attention to the car after the swing, to prevent beginners to control the often turning when the scene.
  (11) to stop turning on the ramp, and should not travel across the ramp.
  (12) forklift cargo downhill, should be retreated to prevent the goods down.
  (4) loading and unloading
  (1) forked items, should be adjusted on the two fork fork distance, so that the fork load balance, not skew, the items should be attached to the side of the shelves, forked components should fit the load base curve signs.
  (2) the height of the carrier shall not obscure the vision of the driver.
  (3) It is necessary to brake the forklift with the brake during the loading and unloading of the article.
  (4) forklift near or evacuation items, the speed should be slow and smooth, pay attention to the wheels do not rolling items, wooden mats, etc., to prevent the rolling material from flying.
  (5) When the goods are taken with the fork, the fork shall be so deeply cut into the load, and the cargo fork can not be touched against other goods or objects. Should use the smallest mast to tilt the load to prevent the load back sliding. When the load is released, the mast can be tilted in a small amount to accommodate the load and the fork.
  (6) to stop the high-speed fork to take the goods and with a fork and hard objects bump.
  (7) forklift work, to prevent people standing on the fork.
  (8) forklift fork work, to prevent people standing around the fork, to prevent the goods collapsed wounding.
  (9) to stop the use of fork lift personnel engaged in high work, to prevent the occurrence of high fall off the incident.
  (10) prohibit the use of brake inertia items.
返回列表

上一页:没有了…

下一页:internal combustion forklift

相关资讯